Creating unique and top quality jewels is a process that involves many procedures to create designs that will attract your customers. Various firms engaged in the production of ornaments have to provide products that will satisfy their customers. Every step matters when the production process is ongoing. Also, the right materials have to be used. This article will dwell on techniques involved in Tufa casting custom jewelry NM.
Stone preparation is the first step for those involved in this process. One has to find the right size of stone that fits the description of the designs they have in mind. After the proper size has been found, it is essential the two sides are flattened and left in a smooth state. The two sides need to be perfectly flat and identical to each other.
With stones ready, sketching the designs of models that one had thought of begins. Here one ought to be keen and do the job in a quiet environment to avoid disturbances which might result in errors. Also, a lot of time needs to be put when making the sketches.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Carbonizing of the stone happens at this point and comes before silver is poured. Pieces of stone can be attached using pieces of rubber or clamps. Silver contents are placed in a crucible and heated at a certain temperature to melt. When silver has reached its melting state, it is then poured into the intended place, and the results should be achieved within a short time.
The surface of these products is cleaned using sand. When sand is used in the cleaning process, it removes parts that are deemed unnecessary, and this does not affect the texture of these products. The other cleaning agents are citric pickling solutions which are also useful in making the surfaces appear clean. Cleaning is also aimed at getting rid of fire traces that sometimes are acquired when the soldiering process begins.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
On completion of most processes, the products are almost ready for the market. Although they are available, there is room for designers to put various styles on them before they are sold. This can be done keeping mind your target market and what you intended to create. As much as other stages take a lot of time, sanding and polishing take the most time.
Stone preparation is the first step for those involved in this process. One has to find the right size of stone that fits the description of the designs they have in mind. After the proper size has been found, it is essential the two sides are flattened and left in a smooth state. The two sides need to be perfectly flat and identical to each other.
With stones ready, sketching the designs of models that one had thought of begins. Here one ought to be keen and do the job in a quiet environment to avoid disturbances which might result in errors. Also, a lot of time needs to be put when making the sketches.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Carbonizing of the stone happens at this point and comes before silver is poured. Pieces of stone can be attached using pieces of rubber or clamps. Silver contents are placed in a crucible and heated at a certain temperature to melt. When silver has reached its melting state, it is then poured into the intended place, and the results should be achieved within a short time.
The surface of these products is cleaned using sand. When sand is used in the cleaning process, it removes parts that are deemed unnecessary, and this does not affect the texture of these products. The other cleaning agents are citric pickling solutions which are also useful in making the surfaces appear clean. Cleaning is also aimed at getting rid of fire traces that sometimes are acquired when the soldiering process begins.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
On completion of most processes, the products are almost ready for the market. Although they are available, there is room for designers to put various styles on them before they are sold. This can be done keeping mind your target market and what you intended to create. As much as other stages take a lot of time, sanding and polishing take the most time.
About the Author:
Get a summary of the things to keep in mind when choosing a tufa casting custom jewelry NM designer and more information about an experienced designer at http://www.bojoejewelry.com now.
Aucun commentaire:
Enregistrer un commentaire